Shreveport Mold Pros logo Shreveport Mold Pros

Mold Remediation

HVAC and Air Duct Mold Remediation in Shreveport, LA

HVAC and air duct mold remediation in Shreveport, LA — coil, plenum and ductwork cleaning with the condensation and drainage faults corrected, so the system stops distributing spores through the house.

  • ✓Shreveport Based
  • ✓Mon–Sat 7:00 AM – 7:00 PM
  • ✓Caddo & Bossier Parish

An HVAC system with mold in it is not a contained problem. It is a distribution system, and every cycle moves spores from wherever they are growing into every room with a supply register. That is what makes duct and air handler contamination different from a localized colony: the symptom is usually whole-house, with a musty smell that arrives when the system kicks on and allergy complaints that track the thermostat rather than any one room.

Why Shreveport Air Handlers Grow Mold

An air conditioner is a dehumidifier that happens to cool. In Shreveport, where cooling runs most of the year against humid subtropical air, the evaporator coil is wet almost continuously through the long season, and the drain pan beneath it holds standing water. That is a permanently damp, dark, dust-fed environment — close to ideal.

Four faults turn that normal dampness into growth. A clogged condensate drain line, which backs water up into the pan and overflows into the plenum and surrounding insulation; the line is usually a short PVC run that collects biofilm and blocks every few years. An oversized system, which cools the air quickly and shuts off before it has run long enough to remove humidity, leaving the house at 60% relative humidity and the ductwork sweating. Duct leakage in a hot attic or damp crawl space, which pulls humid unconditioned air into the system and condenses it inside the ducts. And undersized or bypassed filtration, which lets dust accumulate on the wet coil and feed the colony.

Flex Duct: Clean or Replace

The answer depends on the material. Sheet metal ducts and rigid fiberboard plenums can be cleaned mechanically with HEPA-filtered negative air and agitation, then treated with an antimicrobial labeled for HVAC use. Flexible duct with a contaminated interior liner is a different matter: the liner is porous, it cannot be reliably cleaned once growth has established in it, and the industry answer is replacement.

This distinction matters because duct cleaning is widely sold as the universal fix. Running a brush through contaminated flex duct redistributes spores and leaves the colony in the liner. If the inspection finds growth inside flexible duct, replacing those runs is the honest scope — and in a Shreveport attic, where flex duct spends its life in extreme heat and humidity, that is a common finding.

The Correction Is Mechanical, Not Chemical

Cleaning a coil and fogging an antimicrobial through the ducts without touching the cause buys a few months. The corrections that hold are mechanical: clear and re-pitch the condensate drain and add a safety float switch so a future clog shuts the system down instead of flooding the plenum; seal duct leakage so the system stops drawing in attic and crawl space air; verify the system is not oversized for the house, since short cycling is the root of most high-humidity complaints in Shreveport; and fit filtration that actually seals in its track, since air bypassing a filter is the same as having none.

For homes where humidity stays high even with a correctly sized system, a whole-house dehumidifier tied into the return is the durable answer in this climate.

Related Work

An HVAC system is usually the distributor rather than the origin. Ductwork running through a damp crawl space or a humid attic draws unconditioned air through leaking joints and condenses it inside the ducts, so the system and the space it passes through are typically one project. A condensate line overflowing above a finished ceiling frequently presents as bathroom mold. Growth on saturated plenum insulation after a pan has been overflowing for seasons is covered under black mold removal. For offices, retail and multifamily buildings with packaged rooftop units, see commercial mold remediation. Independent mold clearance testing is worth running after duct work, since the system touches every room.

Technician insight

In Shreveport, check the condensate drain before anything else. A ten-dollar blockage in a short PVC run overflows the pan, soaks the plenum insulation, and seeds the whole duct system — and because the pan is out of sight, it has usually been happening for two or three summers by the time anyone smells it. Clear it, re-pitch it, fit a float switch. That one correction prevents more HVAC mold here than any amount of duct cleaning.

HVAC and Air Duct Mold Remediation Services We Offer

✓Evaporator Coil and Air Handler Cleaning

Cleaning the coil, blower wheel, drain pan and plenum where a continuously wet surface in Shreveport's long cooling season collects dust and grows the colony that feeds the rest of the system.

✓Air Duct Cleaning and Remediation

HEPA-filtered negative air with mechanical agitation through sheet metal and fiberboard ductwork, followed by an antimicrobial labeled for HVAC use after physical cleaning.

✓Flexible Duct Replacement

Replacement of flex runs with contaminated interior liners, which are porous and cannot be reliably cleaned — a frequent finding in Shreveport attics where flex duct lives in extreme heat and humidity.

✓Condensate Drain Correction

Clearing and re-pitching the drain line and fitting a float safety switch, so the next biofilm blockage shuts the system off instead of overflowing the pan into the plenum.

✓Duct Leakage Sealing

Sealing leaking joints, boots and plenum connections that pull humid attic or crawl space air into the system and condense it inside the ducts.

✓System Sizing and Humidity Assessment

Checking whether an oversized system is short cycling — cooling fast, shutting off before it dehumidifies, and leaving the house near 60% relative humidity, which is the root of most recurring complaints here.

✓Whole-House Dehumidification

A dehumidifier tied into the return for homes that hold high indoor humidity even with a properly sized system, which is the durable answer in a humid subtropical climate.

HVAC and Air Duct Mold Remediation Cost in Shreveport, LA

Service Typical Range What Affects It
Air Handler and Coil Remediation $600–$1,500 Coil, blower wheel, drain pan and plenum cleaning and treatment
Duct Cleaning — Sheet Metal or Fiberboard $700–$2,000 HEPA negative air with mechanical agitation, whole system
Flexible Duct Replacement $35–$90 / linear ft Where the interior liner is contaminated and cannot be cleaned
Full System Remediation $3,000–$6,000 Air handler, ductwork and partial flex replacement
Condensate Drain Clearing and Float Switch $150–$400 Clear, re-pitch, and fit a safety shutoff
Duct Sealing $500–$2,000 Sealing leakage drawing attic or crawl space air into the system
Whole-House Dehumidifier, Tied to Return $2,000–$3,500 For homes holding high humidity despite correct system sizing

Ranges are typical for Shreveport, LA and confirmed with an exact written quote before any work starts.

How it works

  1. 1

    System Inspection and Scope

    Open the air handler and inspect the coil, blower, drain pan and plenum, then borescope the supply and return ducts to establish how far contamination actually extends.

  2. 2

    Identify Duct Materials

    Determine which runs are sheet metal, fiberboard or flexible duct. This decides what can be cleaned and what has to be replaced, and it sets the real cost of the project.

  3. 3

    Find the Moisture Fault

    Check the condensate drain for blockage and pitch, test for duct leakage drawing in attic or crawl space air, and assess whether the system is oversized and short cycling.

  4. 4

    Containment

    Seal supply and return registers and set up HEPA-filtered negative air so cleaning does not push spores into the living space.

  5. 5

    Clean and Replace

    Mechanically clean coil, blower wheel, pan, plenum and cleanable ductwork; remove and replace flexible runs with contaminated liners.

  6. 6

    Treat After Cleaning

    Apply an EPA-registered antimicrobial labeled for HVAC application once physical cleaning is complete — after removal, not instead of it.

  7. 7

    Correct the Cause

    Clear and re-pitch the condensate drain with a float safety switch, seal duct leakage, upgrade filtration, and address sizing or humidity with dehumidification where needed.

  8. 8

    Document

    Deliver before and after photographs, the duct material inventory, the faults corrected, and a written scope of work.

Pricing

HVAC and duct mold remediation in Shreveport typically runs $1,500 to $6,000. National ranges for full system remediation run $3,000 to $10,000, with the top end driven by flexible duct replacement rather than cleaning.

Good to know

HVAC and Air Duct Mold Remediation — FAQs

Still have questions? We're happy to talk it through.

(318) 858-4231
+ How much does HVAC and duct mold remediation cost in Shreveport?
Typically $1,500 to $6,000. Air handler and coil work alone runs $600 to $1,500; whole-system duct cleaning $700 to $2,000. National ranges for full HVAC remediation run $3,000 to $10,000, and the top of the range is almost always flexible duct replacement rather than cleaning.
+ Can mold in air ducts be cleaned, or do the ducts need replacing?
It depends on the material. Sheet metal ducts and rigid fiberboard plenums can be cleaned mechanically and treated. Flexible duct with a contaminated interior liner cannot be reliably cleaned because the liner is porous, and the industry answer is replacement. Running a brush through contaminated flex duct mostly redistributes spores.
+ Why does my AC smell musty when it starts up?
That is the signature of growth on the evaporator coil or in the drain pan. In Shreveport the coil is wet almost continuously through the long cooling season, and dust reaching it past a poorly sealing filter gives the colony something to feed on. The smell arrives with the blower because the system is distributing it.
+ What causes mold in a Shreveport HVAC system?
Four faults. A clogged condensate drain backing water into the pan and overflowing into the plenum. An oversized system that cools fast and shuts off before it dehumidifies, leaving the house near 60% humidity. Duct leakage pulling humid attic or crawl space air into the system. And filtration that lets dust bypass onto the wet coil.
+ Will duct cleaning alone solve the problem?
Not if the cause is still there. Cleaning the coil and fogging an antimicrobial buys a few months if the drain is still clogging, the ducts are still leaking attic air, or the system is still short cycling. The corrections that hold are mechanical, not chemical.
+ What is a float switch and why does it matter?
A safety shutoff on the condensate drain. When the line blocks with biofilm — which is normal every few years — the float switch stops the system instead of letting the pan overflow into the plenum and surrounding insulation. It costs very little and it prevents the most common cause of HVAC mold in this climate.
+ Can mold in the HVAC system affect the whole house?
Yes, and that is what distinguishes it from a localized problem. Every cycle carries spores from the coil or ductwork to every room with a supply register. Whole-house symptoms that track the thermostat rather than one room are the usual sign the system itself is the source.

Need Mold Removal in Shreveport, LA?

Talk to a local Shreveport mold removal and remediation crew serving Shreveport and nearby neighborhoods. Every mold removal project starts with a written scope naming the contaminated area, what gets removed versus cleaned, and who corrects the water source — with published price ranges you can compare before you call.

Business hours

Mon–Sat 7:00 AM – 7:00 PM

5782 St Vincent Ave, Shreveport, LA 71108

Call now Get a quote